Schaltplan Armaturenbeleuchtung Durango -03

Dodge-Forum

Help Support Dodge-Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

tja

Registriert
25. Juli 2014
Beiträge
66
Reaktionspunkte
0
Ort
Sellstedt
Hallo,
die Beleuchtung der Armaturen meines Durango -03 funktioniert nicht mehr.
Anfangs hat es einige Minuten gedauert bis sie funktionierte. Nun gar nichts mehr.
Den Lichtschalter samt Helligkeitsregler habe ich getauscht.
Hat jemand einen Plan für die Armaturenbeleuchtung oder einen Tipp?
 
Die Beleuchtung des Temp.-reglers ist auch ohne Funktion?
Dann mal die Sicherung 9 im Sicherungskasten seitlich im Dash nachmessen.
Schaltplan ist leider nur vom 2002er Durango.
 

Anhänge

  • Cluster Light.pdf
    124,6 KB · Aufrufe: 99
Danke für die prompte Antwort.
Ist auf dem Plan der Helligkeitsregler/Schalter eingezeichnet?
Wenn es dieser Schalter mit den Kontakten 4,Widerstand,5,6,7 würde es wohl bedeuten, dass Null bis 12 V auf die Lampen geschaltet/geregelt werden. Kein Halbleiter, nichts. Also kann es nur die Sicherung oder eine Unterbrechung sein. Allerdings wird auch die Meilenanzeige noch die Ganganzeige geregelt!
Sicherung werde ich gleich nochmal nachschauen. Auto ist gerade unterwegs.
 
Der Helligkeitsregler ist der Widerstand in der Zeichnung.
Das ist ein Vorwiderstand für die gesamte Beleuchtung und ist in Reihe zur Beleuchtung. Deswegen auch nicht 0-12V am Ausgang.
Geht die Deckenlampe an, wenn du den Helligkeitsregler auf Dome hochdrehst?
 
Ja, die Innenbeleuchtung wird geschaltet und die Sicherung ist in Ordnung.
 
Zuletzt bearbeitet von einem Moderator:
Vergiss die Frage mit der Deckenleuchte, die läuft ja gar nicht über diesen Teil des Lichtschalters.
Liegt auch Spannung an der SIcherung an, wenn du das Licht einschaltest?
Wie sieht es mit der Beleuchtung des Heizungsreglers aus?
 
Das Park Lamp Relay war der Übeltäter.
Ohne den Plan wäre nie auf dieses Relais gekommen.
Vielen Dank nochmal an Dich. =D>
 
Ehrlich gesagt, Standlicht habe ich nicht geprüft. Die nicht vorhandene Tachobeleuchtung war das große Problem.
Allerdings hat beim Öffnen und Schliessen nichts aussen geblinkt.

Ich hätte da noch eine Frage.
Laut Bedienungsanleitung kann man mit einer funktionierenden Fernbedienung zusätzliche Fernbedienungen anlernen.
Ich bekomme nicht mal den Chime wie in der 3. Zeile beschrieben ?!?!
Hast Du da vielleicht auch einen Tipp?

Procedure #1
Step-by-Step How To Programming Instructions:

INSERT a key into the Ignition and TURN the Ignition to the ON position (just before cranking).
PRESS and HOLD the UNLOCK button on a working remote for four (4) to ten (10) seconds.
While holding the UNLOCK button, PRESS the PANIC button for one (1) second and RELEASE both buttons at the same time. A chime will sound within three (3) seconds to indicate entry into Programming Mode.
PRESS ANY button on the same remote until you hear another chime indicating that the remote has been successfully re-programmed. This Step MUST be done within 30 seconds of hearing the first chime in Step 3.
Within the next 30 seconds PRESS ANY button on the next remote to be programmed to your Vehicle.
REPEAT Step 5 for any additional remotes to be programmed to your Vehicle.
Test all remotes. Programming is now complete.
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Procedure #2
Step-by-Step How To Programming Instructions:

Using a working remote, PRESS the LOCK button five (5) times at two (2) second intervals to re-synchronize the remote.
INSERT a key into the Ignition and TURN the Ignition to the ON position (just before cranking).
PRESS and HOLD the UNLOCK button on a working remote for four (4) to ten (10) seconds.
While holding the UNLOCK button, PRESS the PANIC button for one (1) second and RELEASE both buttons at the same time. A chime will sound within three (3) seconds to indicate entry into Programming Mode.
PRESS the LOCK and UNLOCK buttons simultaneously on the same remote then RELEASE. The Vehicle will chime to indicate that it has recognized the remote.
PRESS and RELEASE the UNLOCK button on the same remote. The Vehicle will again chime to indicate successful programming of that remote. This Step MUST be done within 30 seconds of hearing the first chime in Step 3.
Within 30 seconds of completing Step 5, PRESS the LOCK and UNLOCK buttons on the next remote to be programmed and then RELEASE. You will again hear a chime indicating that the Vehicle has recognized the remote.
PRESS and RELEASE the UNLOCK button on the remote. The Vehicle will again chime to indicate successful programming of that remote.
REPEAT Steps 6-7 on any additional remotes to be programmed to your Vehicle.
Test all remotes. Programming is now complete.
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
 
Oben