Ventile einstellen 5,9L 24V

Dodge-Forum

Help Support Dodge-Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Registriert
26. Aug. 2014
Beiträge
51
Reaktionspunkte
0
Ort
lehe/emsland
Tag,
ich wollte die Tage mal nach den Ventilen sehen, habe dazu aber keine Einstelldaten.
Kann da jemand weiterhelfen?

99iger 5,9L 24V


Gruß
Malte
 
Aus dem 2001er Service Manual Seite 1403ff:
STANDARD PROCEDURE—VALVE LASH ADJUSTMENT AND VERIFICATION
NOTE: To obtain accurate readings, valve lash measurements AND adjustments should only be performed when the engine coolant temperature is less than 60° C (140° F).

The 24–valve overhead system is a “low-maintenance” design. Routine adjustments are no longer necessary, however, measurement should still take place when trouble-shooting performance problems, or upon completion of a repair that includes removal and installation of the valve train components.
(1) Disconnect battery negative cables.
(2) Remove cylinder head cover (Fig. 47).

(3) Remove the crankcase breather and vapor canister (Fig. 48).

(4) Using the crankshaft barring tool #7471–B, rotate the engine and align the pump gear mark with the top dead center (TDC) mark on the gear housing cover (Fig. 49).

(5) With the engine in this position (pump gear mark at 12 o’clock), valve lash can be measured at the following rocker arms: INTAKE 1–2–4 / EXHAUST 1–3–5. Measure the valve lash by inserting a feeler gauge between the rocker arm socket and crosshead (Fig. 50). Refer to VALVE LASH LIMIT CHART for the correct specifications. If the measurement falls within the limits, adjustment/resetting is not necessary. If measurement finds the lash outside of the limits, adjustment/resetting is required.


(6) If adjustment/resetting is required, loosen the lock nut on rocker arms and turn the adjusting screw until the desired lash is obtained:
- INTAKE 0.254 mm (0.010 in.)
- EXHAUST 0.508 mm (0.020 in.)
Tighten the lock nut and re-check the valve lash.
(7) Using the crankshaft barring tool, rotate the crankshaft one revolution (360°) to align the pump gear mark to the 6 o’clock position in relation to the TDC mark on the gear housing cover (Fig. 49).
(8) With the engine in this position (pump gear mark at 6 o’clock), valve lash can be measured at the remaining rocker arms: INTAKE 3–5–6 / EXHAUST 2–4–6. Use the same method as above for determining whether adjustment is necessary, and adjust those that are found to be outside of the limits.
(9) Install the cylinder head cover (Fig. 47).
(10) Install the fuel pump gear access cover.
(11) Connect the battery negative cables.
 

Anhänge

  • Valve Lash Limit.jpg
    Valve Lash Limit.jpg
    40,8 KB · Aufrufe: 281
  • Valve Lash 50.jpg
    Valve Lash 50.jpg
    60 KB · Aufrufe: 290
  • Valve Lash 49.jpg
    Valve Lash 49.jpg
    38,1 KB · Aufrufe: 260
  • Valve Lash 48.jpg
    Valve Lash 48.jpg
    43,9 KB · Aufrufe: 263
  • Valve Lash 47.jpg
    Valve Lash 47.jpg
    73,4 KB · Aufrufe: 239
Auch wenn der Thread schon uralt ist
8)


Vielen Dank an Diefenbaker:

Bin nämlich auch gerade damit beschäftigt und hatte widersprüchliche Angaben bekommen :roll: und war dadurch etwas irritiert.
 
Oben